Sonic Mighty 4K:Post-Processing•
Posted on March 09 2021
Once you have finished printing out 3D models from your Sonic Mighty 4K LCD 3D printer, your prints need to be cleaned and post-processed thoroughly. In this article, we'll demonstrate how to thoroughly clean your 3D models:
Step 1: Getting Prepared
Please prepare a bottle of Phrozen Wash or 95% alcohol, IPA, paper towels, and a cardboard box for discarding post-processing waste materials such as: failed prints, supports, rafts, and/or paper towels that contain uncured resin.
*Note: Please proceed with caution as liquids may be flammable.
Step 2: Clean the Building Plate
Remove the plastic case of the resin 3D printer. Loosen the building plate knob to remove the building plate. Then use a paper towel to wipe the edges and the top of the building plate.
Step 3: Remove the 3D Model from the Building Plate
Place the building plate on a flat, stable surface. Then use the metal scraper included in your toolbox to remove the model.
If you’re having trouble with removing your 3D prints, use a utility knife.
Step 4: Clean the Model
Clean your Models with an Ultrasonic Cleaner
Make sure to prepare two basins and an Ultrasonic Cleaner with Phrozen Wash or 95% alcohol, IPA. Wash your 3D model in each basin and rinse for roughly 3 minutes. Then carefully place the 3D model into the Ultrasonic Cleaner and let it soak for 3 minutes.
*Note: As liquids may be flammable and tend to evaporate fast, make sure to store the liquid in an airtight container after cleaning your 3D prints.
Clean your Models without an Ultrasonic Cleaner
If you don’t currently own an Ultrasonic Cleaner, please prepare two basins, and fill both with Phrozen Wash or 95% alcohol, IPA. Wash your 3D model in each basin and rinse for roughly 1-3 minutes. Continue to wash the model until its surface is clean. You may use a soft brush and slightly brush the model for better results.
*Note: A toothbrush is not recommended as it may cause scratches on the 3D print.
Step 5: Remove Supports from the 3D Model
If you haven’t printed the Phrozen rook .ctb file, your 3D model may have supports attached onto it. You might need to remove the tree-like support structures attached to your model by carefully snipping off the supports with a snip cutter — without damaging the surface of the print. Click here to learn more about the importance of setting supports.
*Note: You can also choose to remove the supports on your 3D prints after post-curing.
Step 6: Dry the 3D Model
Before moving onto post-curing, leave the model to dry in a shaded area for 30-60 minutes. Make sure there is no uncured resin left on the 3D print. You can also use a compressed air gun to fasten the process.
Step 7: Post-Curing
After your model is completely dry, place it directly into a Phrozen Curing Unit or use direct sunlight to cure your 3D prints. If you cure your models under sunlight, you will need to turn it around every few hours so that every part of the model is exposed to sunlight.
Keep in mind that sunlight may not provide equal exposure of light to every part of your model as the direction of the sun changes throughout the day. This may cause your models to cure unevenly, which could result in discoloration. Click here to learn more.
Step 8: Final Result
Volume or Details? Get Both with the Sonic Mighty 8K
If you’ve seen our launch video for the Sonic Mighty 8K, you must have seen the three main models that we choose to represent the powerful details ...Read More
Why the Sonic Mighty 8K is Your Best Bet Yet
Designed specifically to be the most versatile printer in its class, the Sonic Mighty 8K resin 3D printer is equipped with a 10” LCD screen while m...Read More
Get To Know Your Sonic XL 4K 2022
In this article, we’ll introduce you to the Sonic XL 4K 2022 and tell you all about the components and tools that are included in the tool box.Read More